A noisy stud wall is rarely fixed by fitting the first insulation roll on the shelf. For anyone asking which insulation reduces noise, acoustic mineral wool is usually the strongest all-round answer for internal walls, floors and ceilings. But the insulation is only one part of the job. Board mass, airtightness, gaps around services and the way the lining is fixed can make the difference between a worthwhile improvement and a wall that still carries every conversation.
For refurbishments, loft conversions, flats, home offices and separating walls in busy properties, the right approach is a complete acoustic build-up rather than insulation alone. Choose the material to suit the cavity and noise source, then make sure the installation does not create easy paths for sound to travel.
Which Insulation Reduces Noise in Walls and Ceilings?
Acoustic mineral wool – usually supplied as slabs or rolls of glass mineral wool or stone mineral wool – is the go-to material for reducing airborne sound in partition walls, ceiling voids and timber floors. It is fibrous and open-textured, so it absorbs sound energy inside the cavity instead of allowing it to bounce around and pass through the lining.
For most domestic stud partitions, a 50mm, 70mm or 100mm acoustic mineral wool product fitted to fill the void is a practical choice. The exact thickness depends on the stud depth. A 70mm slab in a 70mm timber or metal stud cavity is generally preferable to leaving an air gap, provided it is not tightly compressed. Compression reduces the material’s effectiveness and makes fitting harder.
Stone mineral wool is often selected where fire performance, density and sound absorption are priorities. Glass mineral wool can be lighter to handle and cost-effective across larger areas. Both can perform well acoustically when they are specified for acoustic use and installed properly.
The important distinction is that mineral wool absorbs sound within a cavity. It does not, by itself, stop all sound transmission. Sound can still pass through lightweight plasterboard, around unsealed edges or through connected timber joists and studs.
Why PIR Is Not the First Choice for Soundproofing
PIR insulation boards are excellent where thermal performance is the main requirement and space is limited. They are widely used in roofs, external walls and floors because a relatively thin board can deliver strong thermal resistance. They are not normally the best choice when the key brief is reducing noise.
Rigid foam boards do not absorb airborne sound in the same way as mineral wool. In a stud wall, replacing acoustic mineral wool with PIR may help retain heat but will usually offer less improvement against voices, television sound and general household noise. This does not make PIR the wrong product – it simply needs to be used for the job it is designed to do.
Where a wall needs both insulation and acoustic improvement, the build-up needs more thought. Depending on the available depth and construction, a combination of thermal insulation, an acoustic lining system and suitable plasterboard may be needed. Avoid assuming that an insulation board marketed for thermal use is an acoustic solution as well.
Sound Absorption vs Sound Insulation
These terms are often used interchangeably on site, but they describe different jobs.
Sound absorption reduces echo and reverberation within a room or cavity. Acoustic mineral wool does this well. It is particularly useful in stud walls and suspended ceilings, where the material limits the sound energy building up in the empty void.
Sound insulation, also called sound reduction, limits the amount of sound that travels from one room to another. This relies heavily on mass, separation and airtightness. A double layer of acoustic plasterboard, correctly sealed around the perimeter, will generally block more sound than a single lightweight board. A resilient bar system can improve matters further by reducing direct contact between the board and the framing.
The best acoustic partitions combine both principles: mineral wool in the cavity to absorb sound, dense boards to add mass, and a separated lining where the specification and budget justify it.
Choosing Insulation for Common Building Jobs
Stud partition walls
For a new internal stud wall, fit acoustic mineral wool between the studs, taking care to cut it accurately around noggins, cables and pipework. Follow this with suitably heavy plasterboard on both sides. Where noise control matters – for example between a bedroom and bathroom, office and living area, or a media room and neighbouring space – consider two layers of acoustic plasterboard with staggered joints.
A resilient bar fixed across the studs before boarding can reduce vibration transfer through the frame. It is a useful upgrade, but it only works if installed correctly. Screws that accidentally bridge through the bar into the stud can compromise the system.
Timber floors between rooms
Impact noise from footsteps, dropped items and moving furniture needs a different response from airborne noise. Mineral wool between the joists helps reduce airborne sound, but it will not fully deal with footfall because the vibration travels through the floor structure.
For better results, use acoustic mineral wool between joists alongside a floor treatment that separates the finished deck from the structure. Acoustic overlay boards, resilient layers or a floating floor detail may be appropriate. Below the joists, resilient bars and additional plasterboard layers can also improve the ceiling beneath.
Ceilings below occupied rooms
If the problem is noise from above, filling the void with mineral wool is a sensible first step. However, lifting floorboards above is not always practical in an occupied property. A suspended acoustic ceiling below the existing ceiling can be more realistic, using acoustic mineral wool in the void, resilient bars or acoustic hangers, and one or two layers of acoustic plasterboard.
This reduces headroom, so measure carefully before specifying the build-up. In older properties with low ceilings, a thinner system may be the better compromise even if it does not provide the highest possible acoustic performance.
External walls and loft conversions
For external walls, traffic noise can be affected by windows, vents and doors as much as the wall itself. Insulating a cavity or lining an internal wall may help, but poorly sealed window frames or trickle vents can remain the weak point. Check the whole elevation before spending money on a wall-only solution.
In a loft conversion, mineral wool between rafters or studwork can assist with sound control, while PIR may still be necessary to meet the thermal design within a restricted roof depth. A layered specification can balance heat loss, room size and acoustic comfort, but it should be designed around the construction rather than assembled from leftover materials.
The Details That Make or Break Acoustic Performance
Gaps are the enemy of sound control. Even a well-insulated partition can underperform if there are open perimeters, unsealed service penetrations, back-to-back socket boxes or gaps at the head and sole plates. Use an appropriate acoustic sealant at board edges and around penetrations, following the product guidance and any fire-stopping requirements.
Avoid leaving mineral wool loose, folded or incomplete around obstructions. It should fill the cavity evenly without being crammed in. Equally, do not assume denser always means better. A product made for acoustic cavities, installed at the correct thickness, is more useful than a random high-density board that does not suit the framing.
Flanking transmission also matters. Sound may travel around a new partition through the floor, ceiling, adjoining walls or continuous joists. This is why a basic stud wall can make a noticeable improvement but may not create true privacy between rooms. Higher-performance work, particularly conversions and separating floors, should be considered against the relevant Building Regulations requirements, including Approved Document E where applicable.
A Practical Specification to Start With
For many internal refurbishment jobs, a dependable starting point is a timber or metal stud frame fully filled with acoustic mineral wool, then lined with acoustic plasterboard. Upgrade to double-layer boards and resilient bars where the room use demands greater privacy or where the noise source is persistent.
If the priority is heat retention, do not automatically replace the acoustic wool with PIR. Set out the thermal target, acoustic target and available depth first. That prevents expensive rework and makes ordering straightforward – the right thickness of insulation, matching board quantities, fixings, sealant and any resilient system can all arrive together.
For trade jobs across Hertfordshire and nearby London, WelBM can help source the insulation, plasterboard and timber needed for a practical build-up. Start with the cavity depth and the type of noise you are trying to control, then specify the system around those two facts. That is the quickest route to a quieter room that performs as intended.

