A 100mm PIR board can achieve the sort of thermal performance that may need considerably more depth from a fibrous insulation. That is why it remains a regular choice for extensions, roof upgrades, floors and timber-frame work where every millimetre counts. This PIR insulation review looks beyond the headline lambda value, covering where the board earns its place, where it needs more care on site, and what to check before pricing a job.
What PIR insulation is designed to do
PIR, or polyisocyanurate, is a rigid foam insulation board usually faced with foil on both sides. Its main advantage is high thermal resistance in a relatively thin board. Typical declared thermal conductivity values are around 0.022 W/mK, although the exact figure varies by product, thickness and manufacturer.
For builders, that means a better U-value can often be achieved without losing as much room internally or increasing the build-up of a roof or floor. On a loft conversion, for example, PIR between and below rafters can help hit the target U-value while retaining useful headroom. In a solid-wall refurbishment, insulated plasterboard or a separate PIR lining may be the practical route where external insulation is not an option.
The board is firm, light enough to handle easily and available in a broad spread of thicknesses. It cuts cleanly with the right saw and is straightforward to transport compared with bulkier alternatives. Those are genuine site benefits when materials need to move through a house, up scaffolding or into a tight roof space.
PIR insulation review: thermal performance versus real-world fitting
The quoted lambda value is only part of the job. PIR performs very well when boards are fitted tightly, joints are sealed where the system requires it, and the full construction is detailed properly. Gaps around board edges, poorly cut penetrations and uninsulated timber all reduce the finished performance.
A board may look tight from a distance but still leave air paths behind it. In a pitched roof, small gaps around rafters, roof windows and service runs can undermine the work. In floors, unsupported or uneven boards can move, leaving joints open over time. Measure bays individually rather than assuming every timber centre is identical, particularly in older properties.
Foil-faced PIR can also contribute to vapour control when joints are correctly taped, but it should not be treated as an automatic replacement for a specified vapour control layer. Whether one is needed depends on the build-up, moisture risk and the manufacturer’s system guidance. Warm roofs, bathrooms, kitchens and timber-frame walls all deserve proper thought before boards are ordered.
The same applies to U-value calculations. Do not price a thickness from a rule of thumb alone. Account for rafters, joists, studs, masonry, plasterboard, linings and any thermal bridges. The difference between a nominal target and a compliant construction can be significant, especially where Building Regulations work is involved.
Where PIR boards work best
PIR is particularly strong where thickness is restricted. It is widely used in pitched roofs, flat roofs, suspended timber floors, solid floors, cavity closers, internal wall linings and timber-frame panels. Each use has a different detail, so the right board is not simply the cheapest board of the required thickness.
For pitched roofs, a common approach is insulation between rafters combined with an uninterrupted layer below them. The continuous under-rafter layer limits thermal bridging through the timber. If the roof needs to remain ventilated, maintain the required ventilation gap and follow the roof design rather than packing every void with board.
For warm flat roofs, PIR is often specified above the deck because it keeps the structural deck on the warm side of the insulation. Here, compatible membranes, falls, fixings and loading requirements matter as much as the insulation itself. A standard internal-wall board is not a substitute for a roof system board simply because the thickness matches.
In floors, PIR can be a good fit beneath screed or within a suspended timber construction. Check compressive strength, edge support and the membrane arrangement. For ground-bearing slabs, the insulation has to suit the expected load and the floor build-up. Around services and perimeter edges, careful cutting is worth the time.
Internal wall insulation is often where PIR delivers the greatest gain for the least lost floor area. However, it changes the moisture behaviour of an existing wall. Assess the wall condition first, deal with rain penetration or defects, and use a suitable system detail. Insulating over a damp wall is not a repair.
The trade-offs: cost, fire and acoustic performance
PIR is not the answer for every insulation job. It normally costs more per square metre than mineral wool or EPS, even though its high thermal performance can reduce the thickness required. If there is ample void depth, a mineral wool solution may be more cost-effective and easier to fit around irregular services.
Acoustic performance is another consideration. PIR is primarily a thermal insulant. Mineral wool is generally the better choice where airborne sound reduction is a key part of the build-up, such as internal partitions, separating floors or stud walls around noisy rooms. Many projects use both materials for good reason: PIR for thermal efficiency and mineral wool for acoustic control and cavity filling.
Fire performance needs a clear-headed approach. PIR is an organic foam insulation and is combustible. A board’s facing, test classification or product literature must not be confused with the fire performance of the completed wall, floor or roof. The required lining, cavity barriers, fire stops, fixings and system specification all matter. Follow the design, the relevant Approved Document and the manufacturer’s installation guidance, particularly on higher-risk or multi-occupancy work.
PIR boards can be affected by prolonged exposure to weather and should be kept dry, flat and protected on site. Avoid leaving packs uncovered in standing water or direct sun for extended periods. Damaged edges and crushed corners make tight fitting harder, so it is worth checking deliveries before the boards are carried through the job.
Choosing thickness without over-ordering
Thickness should follow the target U-value and build-up, not a guess based on what was used on the last job. Common board thicknesses range from thinner lining boards through to 100mm, 120mm and 150mm-plus sections for roofs and floors. Thicker is not always better if it compromises ventilation, service zones, door thresholds or required clearances.
For a straightforward refurbishment, start with the available depth and work back from the target performance. For new work, establish the full construction first, including structural members and finishes. If the calculation is tight, a small change in board thickness or a continuous layer can make the difference without creating awkward details elsewhere.
Also check board size against access and cutting waste. Large sheets speed up open areas but can be inconvenient in a confined loft or narrow stairwell. Plan cuts around rafter centres, joist bays and window reveals where possible. Ordering an extra allowance for offcuts is sensible, but excessive waste removes the value from a competitive board price.
Fitting PIR properly on site
Good PIR installation is methodical rather than complicated. Boards should be cut accurately, fitted with edges tight, supported where required and fixed using the specified method. Avoid forcing boards into undersized gaps, as bowed edges can leave voids behind the board.
Use suitable insulation fixings, adhesive or mechanical restraint for the application. Tape foil joints where required by the system detail, and seal around pipes, cables and awkward openings with compatible materials. Electrical cables need consideration too: insulation can affect cable heat dissipation, so do not bury or alter cable routes without checking the electrical design.
Keep the work sequence practical. Complete first-fix services before closing insulated walls and ceilings, photograph concealed details where useful, and inspect joints before plasterboard goes up. It is much cheaper to correct a gap at that stage than after skimming and decoration.
For regular trade requirements, WelBM can help match PIR thicknesses and associated board materials to the build-up, with stock-focused ordering for jobs across Hertfordshire and nearby London areas.
Is PIR worth using?
PIR is worth the premium when thermal performance must be delivered in a limited depth, and when the installation team has the detail under control. It is especially useful in roofs, floor upgrades and internal linings where space carries a cost. It is less compelling where the void is generous, acoustic performance leads the specification, or a lower-cost material meets the required U-value more simply.
The best result comes from treating insulation as part of a complete construction, not as a board thickness on a take-off. Check the specification, protect the boards, cut them accurately and close every gap before the lining goes on. That is how PIR earns its reputation on site.

